How Many Solar Panels to Run a 1 HP Well Pump? (The Exact Math, No Salesman)

Written by Dr. Robert Kowalski — Ph.D. in Agricultural and Biological Engineering from Penn State University, with 18 years of experience in on-farm water systems and solar pumping design. He has sized solar pumping systems for livestock, irrigation, and domestic wells across the Midwest and Northeast. He is a licensed Professional Engineer and a member of the American Society of Agricultural and Biological Engineers.

The honest answer is 4 to 8 panels — and where you land in that range depends on three numbers most installers never ask about: your well depth, your daily water demand, and your sun hours. Here is the five-minute calculation that replaces the sales pitch.

The Problem

Search this question online and you get two useless answers: “it depends” or a number somebody made up. The number is not made up — it is computed, and the computation is short. But it requires three inputs that generic answers skip:

  1. Total dynamic head (TDH) — how far the water is actually lifted: static water level + drawdown + elevation rise + pipe friction. Not the well’s drilled depth — the water’s depth. This is the number that changes everything, and the one nobody asks about.
  2. Daily volume — gallons per day the system must deliver.
  3. Peak sun hours — your location’s daily solar resource (4.5–6.5 across most US farm country).

Miss any of the three and you get the classic failure: a “1 HP kit” that works at the showroom depth and delivers half its rated flow at your 180-foot water level.

The 5-Minute Calculation

Step 1 — Convert the job to hydraulic energy.

Water energy per day (watt-hours) ≈ gallons per day × total head in feet × 0.0026

A livestock well delivering 1,200 gallons/day from a 150 ft water level: 1,200 × 150 × 0.0026 ≈ 468 Wh/day of pure water work.

Step 2 — Divide by system efficiency.

Wire-to-water efficiency for a good solar pump system (pump + motor + controller + wiring) runs 35–50%. Using 40%: 468 ÷ 0.40 ≈ 1,170 Wh/day of solar electricity.

Step 3 — Convert to panels.

Panel watts needed ≈ daily Wh ÷ (peak sun hours × 0.75 real-world factor)

At 5 peak sun hours: 1,170 ÷ 3.75 ≈ 312W of panels — one modern 430W panel covers the pumping energy.

Wait — one panel? For the energy, yes. But that is not the whole answer, because of Step 4.

Step 4 — Size for the power, not just the energy.

A 1 HP pump draws 750–1,000W while running and 2–3× that at startup. Direct-drive solar (no battery) only pumps while the sun delivers enough power. To get useful daily volume, the array must hit the pump’s operating threshold early and hold it late — which is why the real-world answer lands at 1,700–3,400W of array: four to eight 430W panels. The array is oversized relative to daily energy so the pump runs 5–7 useful hours instead of 2.

The Sizing Table: 1 HP Pump by Well Depth

Daily target: 1,200 gallons/day, 5 peak sun hours, quality submersible pump, direct-drive with tank storage.

Water level (TDH) Hydraulic energy/day Solar needed/day Array size Panels (430W)
60 ft (shallow) ~190 Wh ~475 Wh ~900–1,700W 3–4
120 ft ~375 Wh ~940 Wh ~1,300–2,200W 3–5
180 ft ~560 Wh ~1,400 Wh ~1,700–2,600W 4–6
250 ft ~780 Wh ~1,950 Wh ~2,200–3,400W 5–8
350 ft (deep) ~1,090 Wh ~2,700 Wh ~3,000–4,300W 7–10

Two moves change every row: store water, not electricity (an elevated tank or oversized stock tank is 10–20× cheaper per unit of storage than batteries), and choose a pump matched to your head — a pump specified for 150 ft run at 60 ft wastes array; run at 250 ft, it stalls.

The Numbers: Complete System Cost

Component Cost (2026)
6 × 430W panels (2.6 kW) 1,100–1,400
Mount, wiring, disconnects 400–700
1 HP solar submersible pump + controller 900–1,600
Float switches, plumbing 200–400
DIY total 2,600–4,100
Installed 5,000–8,500
Equivalent diesel/gas pumping, 10 years 4,000–6,000 fuel + maintenance, plus the hauling

Against a generator hauled to the well every week, solar pumping typically pays back in 2–4 years and then runs free for two decades. The full diesel comparison is in our pumping breakdown.

Expert Tips

1. Measure the water level — never size off drilled depth. A $30 well sounder or a fishing line and weight tells you the number that actually drives the sizing. Drillers’ logs are often a decade stale.

2. Oversize the array, undersize the storage anxiety. Extra panels are cheap ($230 each) and buy you morning and evening pumping hours. Batteries for night pumping are not — put the water up in a tank during the day instead.

3. Match the pump curve to your TDH. Every pump has a head-versus-flow curve. Demand the curve from the seller and find your TDH on it. A seller who cannot produce a pump curve is not a pump seller.

4. Pipe friction is real head. 500 feet of undersized pipe at 10 GPM adds 30–60 ft of effective head. One pipe size up (80)oftenbeatsonepanelup(80) often beats one panel up (230) — do the friction math before buying watts.

5. Check freeze strategy for winter watering. In cold country, the pump is fine underground; the above-ground plumbing is not. Drain-back design or buried lines decide whether the system survives January — our winterizing checklist covers the details.

6. Size to July, verify for December. Livestock demand peaks with heat exactly as solar peaks — direct-drive pumping is the best-aligned load in agriculture. But check December sun hours (often 2.5–3.5) if winter watering matters; you may want one more panel.

Conclusion

Four to eight panels for a 1 HP well pump — computed, not guessed. Measure the water level, count the daily gallons, look up your sun hours, run the three-step calculation, then size the array for power hours rather than daily energy. Store water in a tank instead of electrons in a battery, match the pump curve to your head, and the system will still be filling troughs when you have forgotten what you paid for it.


Frequently Asked Questions

Q: How many solar panels does it take to run a 1 HP well pump?

A: Four to eight modern 430W panels for most farm wells, depending on three numbers: your water level depth (total dynamic head), your daily gallons, and your peak sun hours. Shallow wells (under 100 ft of head) run on 3–4 panels; water at 250 ft needs 5–8. The daily energy for pumping is small — often under 2 kWh — but the array must be sized for enough instantaneous power to run the pump 5–7 useful hours per day.

Q: Can a solar pump work without batteries?

A: Yes — and for farm water, direct-drive with tank storage is the standard, correct design. The pump runs when the sun shines and fills an elevated or oversized stock tank; the stored water covers nights and cloudy stretches. Water storage costs roughly 10–20 times less per usable unit than battery storage, has no cycle-life limit, and never needs a controller update. Batteries only make sense for pressurized domestic supply.

Q: What size solar pump do I need for 200 feet of head?

A: A 1 HP solar submersible rated for that head — but check the pump curve, not the horsepower label. At 200+ ft of total dynamic head, a properly matched 1 HP pump typically delivers 7–12 GPM at solar noon and 1,000–1,800 gallons per day from a 5–8 panel array (2.2–3.4 kW). A pump mismatched to your head can lose half that flow with the same panels, which is why the curve matters more than the sticker.


Related Articles


© 2026 Farm Solar Guide. All data sourced from ASAE water system standards, manufacturer pump curves and panel specifications, and documented US farm operations. Last verified: November 10, 2026

1 thought on “How Many Solar Panels to Run a 1 HP Well Pump? (The Exact Math, No Salesman)”

Leave a Comment